ENART-INVET Biofeedback devices
Schedule
Mo-Fr. 10:00-19:00
Sat. 11:00-16:00
Sun. day off
Allergy treatment with the ENART device

 

allergy-treatment-with-the-enart-device-photoIn this article, we will talk about how to treat allergies, a fairly common disease today, using the ENART® 911-L2 device.

So, what are the main areas treated for allergies?

First, it is necessary to treat the zone of localization of symptoms, depending on the type of allergy.

Let's take hay fever as an example.

Hay fever is a reaction to the pollen of various flowering plants. It occurs, as a rule, at the end of August and lasts until the end of September, sometimes until the end of autumn. Hay fever causes watery eyes and allergic rhinitis.

Thus, the first zone for treatment is the "Six points" zone, i.e. where the trigeminalthe-six-points-zone-photo nerve exits.

To treat the “Six points” zone, set the device to "DIAG 1" mode and frequency FREQ = 60 Hz. 

 

treatment-on-the-left-photo

 

Start treatment on the first point on the left.

 

 

 

Next, treat the second point on the right side, then the third, fourth, fifth and sixth points. Treat each of these six points to the minimum effective "Dose" or to the value "Zero".

If you are worried about a severe runny nose, use "DIAG 1" mode to find priority points near the bridge of the nose, on both sides of the nose, then switch to “FMVAR” mode and treat the found points using this mode. points-near-the-bridge-of-the-nose-photo

This will remove the inflammation and allergic reaction.

 

 

7th-cervical-vertebra-photoFurther, with hay fever, if there is a runny nose, conjunctivitis, lacrimation from the eyes, we recommend treating the area of the 7th cervical vertebra (C7).

This is the most protruding vertebrae if you tilt your head forwards.

Set the device to "DIAG 1" mode and use sound indication to find the priority point. Treat it to "Zero". Also, you can treat it in "CONST" mode. Set the frequency to FREQ = 10 Hz, number of Peaks in the pulse waveform INTENS = 3 and treat this point for 5 minutes.

This is a very important area, it enhances the overall reaction and it is close to the source of the allergic reaction.

Next, it is necessary to treat the area of ​​the liver and intestines - a very important area for allergies.

liver-zone-photo

The liver zone is located in the right hypochondrium.

For treatment of the liver, it is better to use the "SC" mode, which has more priority for working with internal organs. Find in this zone the points that are a priority for treatment, the device will indicate where they are, and treat them.  After treating the liver area to "Zero" in the "SC" mode, you can re-treat it in the "CONST" mode.

We recommend treating the intestinal area in a clockwise direction, starting from the navel, in a spiral, expanding the circle.

zone-of-the-intestine-photo

Set the device to "CONST" mode, FREQ = 60 Hz, INTENS = 3 and treat the zone in motion.

A standard allergy therapy session consists of treating these areas. With a very strong allergic reaction, 3-4 such sessions per day can be performed.

What other areas can be treated in the acute phase of allergy?

suprasternal-notch-area-photoThe area of ​​the suprasternal notch - it is located between the collarbones.

It is very convenient to use the electrodes of the ENART device on this point.

Treat it to "Zero" in the "DIAG 1" mode. As soon as the device gives a signal that the reaction has reached "Zero", you can stop treating. The universal modes "SC", "EN" and "EM" are also suitable for treating this zone.

In the case of allergies, treatment of the kidney and adrenal glands is especially effective.

kidney-area-photo

The zone of the kidneys is located on the back, where the costal arch passes and, as it were, crosses the projection of the kidneys in the middle. 

adrenal-zone-photo

Just above this arc is the area of ​​the adrenal glands. The diagnostic mode "SC" is a priority for working with internal organs, using this mode you can easily find these points and treat them.

cervical-collar-zone-photoAdditionally, you can treat the cervical-collar zone.

Here you can use the "CONST" mode, FREQ = 77 Hz, then 60 Hz, INTENS = 3.

Alternatively, you can use the "SM" mode, find priority points for treatment, and treat them to "Zero".

 

In case of allergic dermatitis, i.e. allergy appearing in the form of rashes, it is necessary to treat the area affected by the rash directly. If this area is wet, use the "MCONST" mode. It can work without direct contact with the skin, at a distance of about 5 mm from the skin.

Place the device directly over the problem area, set the frequency to FREQ = 200 Hz, then 140 Hz, then 100Hz, INTENS = 1 or INTENS = 2 and treat for 5-10 minutes or more.

There are some difficult cases where it must be treated for up to 30 minutes.

Also, treat the area of ​​allergic dermatitis along the perimeter, along the edges, i.e. without touching the rashes themselves.

If the rashes are dry, if they allow you to touch them with the electrodes of the device, you can treat them directly. To do this, you can use the universal modes "SC", "EN", "EM" until the value "Zero" is reached.

Further, some segmental zone should be treated.cervical-region-photo

► For example, if the area of ​​the rash is on the arm, after its treatment it is necessary to treat the cervical region

 

lumbosacral-region-photo► If the rash is on the leg, after treating the area with the rash, it is necessary to treat the segmental zone – the lumbosacral region

 

 

► If it is the stomach, then the thoracic region is treated – on the front and back of the spine. 

thoracic-region-photo

► You can treat the "Three tracks" zone,

three-pathways-photoi.e. along the paravertebral areas – these are the paravertebral lines, near the spinous processes. 

This is how you can treat allergies with the ENART® 911 device. 

After a while, the allergy will stop bothering you or its symptoms will become much weaker.

 

*ENART®  - is a registered trade mark of Consultative and Commercial Center INVET®

 

Comments

Write Comment